How To Repair Fill Valve

Download Article

Download Commodity

A faulty toilet fill valve can cause your toilet to run all the time or otherwise malfunction. All the same, the good news is that replacing your toilet fill valve is something any homeowner can do. It does not have a lot of experience with plumbing or a lot of time. However, you do need a few parts, a couple of tools, and a little bit of endeavour.

1. 1

   Plow off the water supply. Before doing whatsoever repairs to your toilet y'all should turn off the h2o outside of the toilet. You should accept a water valve direct beneath the toilet tank. It should be located betwixt where the water piping comes out of the wall and where it attaches to the bottom of the toilet tank.^[1]

   • In most cases, you will turn the water shutoff valve clockwise to turn information technology off. Be sure to continue turning information technology until information technology stops moving.

   EXPERT TIP

   James Schuelke, along with his twin brother David, is the co-owner of the Twin Home Experts, a licensed plumbing, leak detection, and mold inspection company based in Los Angeles, California. James has over 32 years of home service and business plumbing feel and has expanded the Twin Home Experts to Phoenix, Arizona and the Pacific Northwest.

   

   James Schuelke
   Professional person Plumber

   Information technology's a adept idea to turn off your main h2o valve, besides. Detect the main water shut-off valve on the exterior of your habitation and turn it off. And so, go around your belongings and turn on diverse fixtures to confirm that they're off, just it will also drain off balance water that'south inside the organisation. Doing this volition assist yous avoid water impairment due to a flood.

2. ii

   Drain the toilet tank. Once the water is turned off, drain the tank earlier you lot tin can disconnect the toilet fill up valve. To brainstorm draining the tank, affluent the toilet and hold the flush lever down to remove as much water as possible. One time well-nigh of the water is gone, yous will need to use a turkey baster or a wet-dry vacuum to get rid of the pocket-size amount of water sitting at the bottom of the tank.^[2]

   • If yous don't accept a turkey baster or wet-dry vacuum, use an old towel or sponge to soak upward the remaining h2o and any sediment left in the tank.

   Advertisement

3. iii

   Locate the toilet fill up valve. Remove the tank lid carefully and ready it on a towel out of the way and then it doesn't get broken. The toilet fill up valve is located inside the toilet tank, unremarkably off to one side. In newer toilets, it is the entire plastic column that includes the float and the on-off lever for filling. In older toilets, the float is a separate slice simply it will be continued to the top of the fill valve. ^[3]

   • The fill valve besides has a tube fastened to it that connects to the overflow pipe.^[4]

4. 4

   Detach the toilet fill valve. Loosen the nut that secures the make full valve to the water supply line past turning it counterclockwise with pliers or a wrench. Then, carefully pull the supply line out of the valve underneath the tank.^[5]

   • Every bit you unscrew the nut, a bit of water may drip out of the tank. Proceed a towel on hand or on the floor beneath the opening to catch any water that comes out.

   Ad

1. ane

   Purchase a new toilet fill valve. Go to your local hardware store and purchase a new toilet make full valve. Most new toilet fill valves are universal, significant they will fit in almost any toilet. However, if yous are worried about fit, have your erstwhile toilet valve with yous to the store and employ it to assess whether a potential replacement will work.^[6]

   • Even if your old toilet fill valve had a separate float, a newer valve with the float integrated onto the shaft volition piece of work.

2. 2

   Put the new toilet fill valve in identify. Remove the new toilet fill up valve from its packaging. Be sure to read the directions it comes with. The make full valve should come fully assembled, so you should exist able to put it straight into the toilet.^[vii]

   • Remember to also clip the new refill tube to the overflow tube.

3. 3

   Make sure all the washers are in place. It is important to pay attention to how whatsoever included washers and nuts should be attached to the valve. At that place should be washers on the within and the outside of the tank where the fill valve goes through information technology.^[viii]

   • Washers on the inside and outside of the tank ensure that there is a water-tight seal around this connection signal.

4. 4

   Tighten the fill valve nut carefully. When yous have the toilet fill valve in place, the final part of its installation is to tighten a lock nut onto the threaded part of the valve. This is located on the underside of the tank. When doing this, information technology is important not to tighten the nut too difficult. The nut should exist tightened by mitt to ensure that you don't tighten it too much.^[9]

   • Tightening the nut on the bottom of the fill valve with a wrench or pliers could crack the toilet tank or the valve.

5. 5

   Reattach the h2o supply line and turn on the water. Once the replacement fill valve is in identify, information technology'southward fourth dimension to get the water flowing again. Attach the supply line to the bottom of the new fill valve. Make certain that there is a washer inside the end of the supply line and tighten it with a wrench until information technology's tight. So turn on the water by turning the shutoff valve counter clockwise until information technology stops rotating.^[10]

   • Be careful not to overtighten the washer, or the nut could crack and the connection will leak.
   • If you see whatsoever leaks, immediately turn the water off at the shutoff valve.
   • When you plough the h2o on, the tank should start filling right away.

   Adept TIP

   James Schuelke, along with his twin brother David, is the co-owner of the Twin Dwelling house Experts, a licensed plumbing, leak detection, and mold inspection company based in Los Angeles, California. James has over 32 years of home service and business plumbing experience and has expanded the Twin Dwelling house Experts to Phoenix, Arizona and the Pacific Northwest.

   

   James Schuelke
   Professional Plumber

   Exist very cautious as you turn the water back on. Once the valve is on, plough the primary h2o supply on very slowly, and have a second person go into the bathroom and brand certain in that location are no leaks as you regenerate the water arrangement.

6. 6

   Arrange the float. Once the water is turned back on and your toilet tank has filled, then you tin can adjust the float on your new toilet fill valve. The float'south location can be adjusted with a clip on its side, a prepare screw at the top of the float shaft, or by adjusting a spiral at the superlative of fill valve where the float attaches.^[11]

   • Look at the directions of your new toilet make full valve for exact directions for bladder adjustment.
   • When positioned correctly, the summit of the float should exist fix at nigh one inch (2.5 cm) below the height of the overflow piping. The goal is that the float comes up and shuts off the water before the water gets loftier enough to flow over the top of the overflow pipe.

   Advertizing

Ask a Question

200 characters left

Include your electronic mail address to get a message when this question is answered.

Submit

Advertisement

• If the fill valve is malfunctioning on an older three.v-gallon (13.25-liter) flush toilet, consider replacing the toilet with a 1.five-gallon (five.67-liter) model. It will easily pay for itself in water savings!

Advertisement

Things Y'all'll Need

• A wrench or pliers
• New toilet fill valve kit
• Bucket
• Towel

About This Article

Article Summary X

To supersede a toilet fill valve, kickoff past turning off the water valve directly below the toilet. Next, flush the toilet and concord the lever down to remove as much water as possible from the tank. You can go rid of any excess h2o by using a turkey baster, wet-dry vacuum, or old towels. Then, remove the tank lid and locate the toilet fill valve, which should exist off to one side and connected to the overflow pipe. Detach the valve and put the new valve in its place, remembering to clip it to the overflow pipe. Finally, tighten downwardly all the washers and basics to secure the valve in place, and turn the h2o back on. To acquire how to adjust the bladder on your new toilet fill valve, proceed reading!

Did this summary aid you?

Thanks to all authors for creating a folio that has been read 147,577 times.

Did this article help y'all?

Source: https://www.wikihow.com/Replace-a-Toilet-Fill-Valve

Posted by: millikenthasins46.blogspot.com

Share this post